Posted on April 21, 2023March 5, 2024 by Dale Phillips Constructing an Under-Saddle Transducer Constructing an Under-Saddle Transducer by R.M. Mottola Originally published in American Lutherie #68, 2001 and Big Red Book of American Lutherie Volume Six, 2013 Piezoelectric transducers or pickups (I use the terms interchangeably) are popularly used to “electrify” acoustic instruments, and are increasingly found embedded in the bridge saddles of electric instruments as well. Manufactured transducers are available from a number of sources, but this article provides instructions for making an undersaddle piezo pickup for a flattop guitar from basic materials. If you know which end of a soldering iron to grab hold of, you can build this pickup. Piezo material will generate an electrical charge when mechanically deformed. There are four types of piezo materials used in the manufacture of instrument transducers: lead zirconate titanate (PZT) ceramic chips, PZT ceramic “bender” disks, polyvinylidene fluoride (PVDF) plastic film, and PVDF coaxial cable. PZT chips find their way into first-generation undersaddle guitar transducers, transducers for various bowed instruments, and manufactured archtop guitar and mandolin bridges. PZT disks consist of PZT material bonded to thin brass disks, and are commonly used for soundboard pickups for flattop guitars and for bridge-mounted pickups for upright basses. PVDF film may be found in all sorts of transducers from undersaddle guitar transducers to under-bridge-foot transducers for bass viols. PVDF coax cable is manufactured just like the single-conductor shielded cable used to make instrument cables, except that instead of an insulating material between the center conductor and the outer shielding braid, we find PVDF material. It is used in manufactured undersaddle pickups for acoustic guitars and is the material that will be used to construct a transducer in this article. Become A Member to Continue Reading This Article This article is part of our premium web content offered to Guild members. To view this and other web articles, join the Guild of American Luthiers. Members also receive 4 annual issues of American Lutherie and get discounts on products. For details, visit the membership page. If you are already a member, login for access or contact us to setup your account.
Posted on April 21, 2023March 5, 2024 by Dale Phillips A Special Guitar Neck Modification A Special Guitar Neck Modification by Ralph Bonte Originally published in American Lutherie #103, 2010 Last week I was able to make someone very happy. Christophe contacted me through my website, in pursuit of a luthier who could help him with his problem. Four years ago he had an accident while cleaning up the bushes surrounding his house. He was working with a wood chipper and wearing safety gloves. To make a long and painful story short, had he not worn the gloves he would have lost the tip of his left thumb. Due to the gloves, his thumb got caught in the motor of the chipper and was torn out of his hand, causing troubles for the muscles and tendons in his arm. Christophe used to be a recording artist playing the guitar. It took him four years of physical therapy to overcome and adapt to the new situation. In the past year, the urge to play the guitar again became overwhelming. However, he could no longer play a regular guitar since he lost the support of his left thumb. He tried a prosthesis, but that didn’t work. He found it too awkward. When I read his message, I immediately agreed to do the work, although I did not know how I was going to do it. Become A Member to Continue Reading This Article This article is part of our premium web content offered to Guild members. To view this and other web articles, join the Guild of American Luthiers. Members also receive 4 annual issues of American Lutherie and get discounts on products. For details, visit the membership page. If you are already a member, login for access or contact us to setup your account.
Posted on April 21, 2023March 5, 2024 by Dale Phillips Meet the Maker: Henry Stocek Meet the Maker: Henry Stocek by John Calkin Originally published in American Lutherie #62, 2000 and Big Red Book of American Lutherie Volume Six, 2013 There is a host of nonluthiers without whom lutherie would suffer. I refer to the makers and suppliers of the products that eventually comprise our instruments — the wood, trim items, pickups, cases, hardware, and finish products that make instruments more functional and more interesting. It should come as no surprise that most of these folks are as fascinating and dedicated as any luthier. We’ve met a few of them in these pages before, and I hope to give more of them the exposure they deserve. First up is Henry Stocek, the celluloid guru who introduced us to the art of turtleoid creation (see Reinventing the Celluloid Tortoise). He created Deep River Vintage Instrument Supply to furnish the trade with imitation tortoiseshell pickguard stock that was reminiscent of the color and patterns used in the ’30s. Other items are on the way. Become A Member to Continue Reading This Article This article is part of our premium web content offered to Guild members. To view this and other web articles, join the Guild of American Luthiers. Members also receive 4 annual issues of American Lutherie and get discounts on products. For details, visit the membership page. If you are already a member, login for access or contact us to setup your account.
